Influence of the sample position of the cast on the thermoplasticity of lean duplex stainless steel 2101

FENG Zhi-hui; LI Jian-xing; LI Jing-yuan; WANG Yi-de

doi:10.13374/j.issn2095-9389.2017.09.009

Volume 39 Issue 9

Sep. 2017

Turn off MathJax

Article Contents

Article Navigation > Chinese Journal of Engineering > 2017 > 39(9): 1364-1371

FENG Zhi-hui, LI Jian-xing, LI Jing-yuan, WANG Yi-de. Influence of the sample position of the cast on the thermoplasticity of lean duplex stainless steel 2101[J]. Chinese Journal of Engineering, 2017, 39(9): 1364-1371. doi: 10.13374/j.issn2095-9389.2017.09.009

Citation:

FENG Zhi-hui, LI Jian-xing, LI Jing-yuan, WANG Yi-de. Influence of the sample position of the cast on the thermoplasticity of lean duplex stainless steel 2101[J]. Chinese Journal of Engineering, 2017, 39(9): 1364-1371. doi: 10.13374/j.issn2095-9389.2017.09.009

Citation:

PDF( 9575 KB)

Influence of the sample position of the cast on the thermoplasticity of lean duplex stainless steel 2101

doi: 10.13374/j.issn2095-9389.2017.09.009

School of Materials Science and Engineering, University of Science and Technology Beijing, Beijing 100083, China

Received Date: 2017-04-12

Abstract

Abstract

To understand the reasons behind edge cracks of large-scale cast ingot during hot deformation, this paper compared the compositions, phase ratios at different temperatures, and differences in the hardness of two phases in the middle and edges of cast ingots. The microstructure and fracture morphology of the samples were observed by optical microscopy, scanning electron microscopy, and electron back-scattered diffraction. The results indicate the presence of smaller grains and larger ferrite content in the edge portion than in the middle. However, edge cracking is also more serious than middle cracking, which indicates that grain size and phase proportion are not the main factors influencing the side cracking of ingots. Compared with that of the middle portion, the hardness difference between the two phases of the ingot edge is larger. Thus, the strain distribution of the two phases varies during hot deformation, and stress concentration occurs along the phase boundary. More precipitates are observed in the phase boundary of the ingot edge than in that of the middle specimens, and these precipitates are believed to destroy the continuity of the matrix, leading to microcracks.
- lean duplex stainless steel,
- thermoplasticity,
- phase ratio,
- hardness difference,
- sample position

FullText(HTML)

References(19)

References

[2]	Iza-Mendia A, Pinol-Juez A, Urcola J J, et al. Microstructural and mechanical behavior of a duplex stainless steel under hot working conditions. Metall Mat Trans A, 1998, 29(12):2975
[4]	Zhang L H, Jiang Y M, Deng B, et al. Effect of aging on the corrosion resistance of 2101 lean duplex stainless steel. Mater Charact, 2009, 60(12):1522
[5]	(張麗華.經濟型雙相不銹鋼2101的腐蝕行為研究[學位論文].上海:復旦大學, 2010) Zhang L H. Study on the Corrosion Behavior of Economical Duplex Stainless Steel 2101[Dissertation]. Shanghai:Fudan University, 2010
[7]	Fang Y L, Liu Z Y, Wang G D. Crack properties of lean duplex stainless steel 2101 in hot forming processes. J Iron Steel Res Int, 2011, 18(4):58
[8]	Evangelista E, McQueen H J, Niewczas M, et al. Hot workability of 2304 and 2205 duplex stainless steels. Can Metall Q, 2004, 43(3):339
[10]	Liu Y Y, Yan H T, Wang X H, et al. Effect of hot deformation mode on the microstructure evolution of lean duplex stainless steel 2101. Mater Sci Eng A, 2013, 575:41
[11]	(吳琨.經濟型雙相不銹鋼2101高溫變形行為及機理研究[學位論文].西安:西安建筑科技大學, 2013) Wu K. Study on Hot Deformation Behavior and Mechanism of Economical Duplex Stainless Steel 2101[Dissertation]. Xi'an: Xi'an University of Architecture and Technology, 2013
[12]	Sieurin H, Sandstrom R, Westin E M. Fracture toughness of the lean duplex stainless steel LDX 2101. Metall Mater Trans A, 2006, 37(10):2975
[13]	Zou D N, Wu K, Han Y, et al. Deformation characteristic and prediction of flow stress for as-cast 21Cr economical duplex stainless steel under hot compression. Mater Des, 2013, 51:975
[14]	Park J Y, Ahn Y S. Effect of Ni and Mn on the mechanical properties of 22Cr micro-duplex stainless steel. Acta Metall Sin (Engl Lett), 2015, 28(1):32
[15]	Fang Y L, Liu Z Y, Xue W Y, et al. Precipitation of secondary phases in lean duplex stainless steel 2101 during isothermal ageing. ISIJ Int, 2010, 50(2):286
[16]	Crowther D N, Mintz B. Influence of grain size and precipitation on hot ductility of microalloyed steels. Mater Sci Technol, 1986, 2(11):1099
[17]	El Wahabi M, Gavard L, Montheillet F, et al. Effect of initial grain size on dynamic recrystallization in high purity austenitic stainless steels. Acta Mater, 2005, 53(17):4605
[19]	Ågren J. Computer simulations of the austenite/ferrite diffusional transformations in low alloyed steels. Acta Metall, 1982, 30(4):841
[20]	Atamert S, King J E. Elemental partitioning and microstructural development in duplex stainless steel weld metal. Acta Metallurgica et Materialia, 1991, 39(3):273
[21]	Park Y H, Lee Z H. The effect of nitrogen and heat treatment on the microstructure and tensile properties of 25Cr-7Ni-1.5Mo-3W-xN duplex stainless steel castings. Mater Sci Eng A, 2001, 297(1-2):78
[23]	Hänninen H, Romu J, Ilola R, et al. Effects of processing and manufacturing of high nitrogen-containing stainless steels on their mechanical, corrosion and wear properties. J Mater Process Technol, 2001, 117(3):424
[24]	Cortie M B, Potgieter J H. The effect of temperature and nitrogen content on the partitioning of alloy elements in duplex stainless steels. Metall Trans A, 1991, 22(10):2173
[25]	Dastur Y N, Leslie W C. Mechanism of work hardening in Hadfield manganese steel. Metall Trans A, 1981, 12(5):749